LVS-DR实战：搭建HTTP和HTTPS负载均衡集群

DR模式是通过director将报文源和目标MAC地址修改，发送给RS，RS将响应报文直接发送给client。

环境说明：

LVS服务器（DR）	DIP：192.168.32.125	VIP：192.168.32.250
apache服务器（RS）	IP：192.168.32.130	VIP：192.168.32.250
apache服务器（RS）	IP：192.168.32.135	VIP：192.168.32.250

三台机器分别配置了对应的本地静态地址DIP和RIP，VIP之后配置

1. 搭建lvs-dr模式的http负载集群

LVS服务器配置要点

　　LVS是被编译进内核中，主要分为两部分ipvs和ipvsadm，ipvs是LVS软件核心，是运行在LB上的，这是个基于ip层的负载均衡；ipvsadm是用户空间的集群管理工具。

要想起到负载均衡效果，那么所有请求报文必须发往LVS服务器(DS)，然后DS根据指定算法分发到后端服务器上，因此DS必须配置VIP地址，VIP是与公网client通信地址，这样DS才能接受到请求报文进行分发。

一定要先设置好内核参数在配置VIP，如果先配置VIP，VIP配置好后会立即通告给所有人，而修改内核参数就是为了不通告

LVS-DR模式的注意情况：

VS 的VIP 和 RS 必须在同一个网段，不然广播后所有的包都会丢掉：提前确认LVS/硬件LB 是什么模式，是否需要在同一个网段所有的RS都必须绑定VIP的IP地址，否则RS收到package后发现dst 不是自己的IP，所有包都会丢掉。 RS处理完包后直接把package 通过dst IP 发送给 client ，不通过LVS/迎接IP 了这样的LVS /VIP 效率会更高一点。【通过把realserver的ip暴漏给外界，不是很安全】

1.1 LVS上配置IP

[root@DR ~]# ip addr add 192.168.32.250/32 dev eth0

[root@DR ~]# ip a

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000

    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00

    inet 127.0.0.1/8 scope host lo

       valid_lft forever preferred_lft forever

    inet6 ::1/128 scope host

       valid_lft forever preferred_lft forever

2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000

    link/ether 00:0c:29:39:18:a9 brd ff:ff:ff:ff:ff:ff

    inet 192.168.32.125/24 brd 192.168.32.255 scope global noprefixroute eth0

       valid_lft forever preferred_lft forever

    inet 192.168.32.250/32 scope global eth0

       valid_lft forever preferred_lft forever

    inet6 fe80::20c:29ff:fe39:18a9/64 scope link

       valid_lft forever preferred_lft forever

1.2 RS上配置arp内核参数

[root@RS-1 ~]# vim /etc/sysctl.conf

#添加以下两行

net.ipv4.conf.all.arp_ignore = 1

# 将对应网卡设置为只回应目标IP为自身接口地址的ARP请求

net.ipv4.conf.all.arp_announce = 2

# 将ARP请求的源IP设置为eth0上的IP，也就是RIP

[root@RS-1 ~]# sysctl -p

net.ipv4.conf.all.arp_ignore = 1

net.ipv4.conf.all.arp_announce = 2

##两台RS都要进行以上操作

[root@RS-2 ~]# echo 'net.ipv4.conf.all.arp_ignore = 1' >> /etc/sysctl.conf

[root@RS-2 ~]# echo 'net.ipv4.conf.all.arp_announce = 2' >> /etc/sysctl.conf

[root@RS-2 ~]# sysctl -p

net.ipv4.conf.all.arp_ignore = 1

net.ipv4.conf.all.arp_announce = 2

1.3 RS上配置VIP

一定要先设置好内核参数在配置VIP，如果先配置VIP，VIP配置好后会立即通告给所有人，而修改内核参数就是为了不通告

LVS服务器的eth0网卡的IP:192.168.32.250作为VIP

两台RS上都要做

[root@RS-1 ~] ip addr add 192.168.32.250/32 dev lo

[root@RS-2 ~] ip addr add 192.168.32.250/32 dev lo

#永久生效在配置文件中加IP

所有RS上都要做

[root@RS-1 ~]# route add -host 192.168.32.250/32 dev lo

#永久配置

		echo '192.168.32.250/32 via dev lo' > /etc/sysconfig/network-scripts/route-lo

[root@RS-2 ~]# route add -host 192.168.135.131/32 dev lo

1.4 DR上配置lvs-dr转发规则

#LVS依赖于ipvsadm来进行配置，所以我们首先先安装ipvsadm

[root@DR ~]# yum -y install ipvsadm

[root@DR ~]# ipvsadm -A -t 192.168.32.250:80 -s rr

[root@DR ~]# ipvsadm -a -t 192.168.32.250:80 -r 192.168.32.130:80 -g

[root@DR ~]# ipvsadm -a -t 192.168.32.250:80 -r 192.168.32.135:80 -g

[root@DR ~]# ipvsadm -Sn

-A -t 192.168.32.250:80 -s rr

-a -t 192.168.32.250:80 -r 192.168.32.130:80 -m -w 1

-a -t 192.168.32.250:80 -r 192.168.32.135:80 -m -w 1

[root@DR ~]# ipvsadm -Sn > /etc/sysconfig/ipvsadm

1.5 RS上配置http并启动

[root@RS-1 ~]# yum -y install httpd

[root@RS-1 ~]# echo 'rs1' > /var/www/html/index.html

[root@RS-1 ~]# systemctl start httpd

[root@RS-2 ~]# yum -y install httpd

[root@RS-2 ~]# echo 'rs1' > /var/www/html/index.html

[root@RS-2 ~]# systemctl start httpd

1.6 客户端访问测试

[root@localhost ~]# for i in $(seq 10);do curl 192.168.32.250:80;done

rs2

rs1

rs2

rs1

rs2

rs1

rs2

rs1

rs2

rs1

搭建https的负载集群

在以上配置基础下搭建https

1. LVS服务器搭建CA服务端

1.生成密钥对

[root@DR ~]# cd /etc/pki/CA/

[root@DR CA]# (ls)

certs  crl  newcerts  private

[root@DR CA]# (umask 077;openssl genrsa -out private/cakey.pem 2048)

Generating RSA private key, 2048 bit long modulus

.................................+++

.........................................................................................+++

e is 65537 (0x10001)

[root@DR CA]# openssl rsa -in private/cakey.pem -pubout

writing RSA key

-----BEGIN PUBLIC KEY-----

MIIBIjANBgkqhkiG9w0BAQEFAAOCAQ8AMIIBCgKCAQEAxBHetLa8VvcmikZNDbG/

tXsbrxvCBsMnsMcwqCKLupcZiRhlUgjY+AAYPrBM5sE8jlJAW/mEGZc1fHG30ruU

5Lnbh2NeHrHJZUuZS6WYCslDKzd0KRDW2GR43CtfqLmFc8g+3DWIqEdeXrH29o5L

cm4AsfeqjBQaNIoNXKcnl/7Yc0mJK+yp3AHO4EFadXTQF+nx6A0mfVRw254h4lgP

6YdL3izUlG2JZ5kqZfytMzG1lKz+O651alNo+Lq14mSKxJArLAT5mWvJ/JJXH/7q

qIHk1RPHQ2XkZyk7QONhjLfZN9aY1h3EawAoBH8etbasbUoPWaUeV+wxzDqPF4pY

qQIDAQAB

-----END PUBLIC KEY-----

2.生成自签署证书

[root@DR CA]#  openssl req -new -x509 -key private/cakey.pem -out cacert.pem -days 1024

You are about to be asked to enter information that will be incorporated

into your certificate request.

What you are about to enter is what is called a Distinguished Name or a DN.

There are quite a few fields but you can leave some blank

For some fields there will be a default value,

If you enter '.', the field will be left blank.

-----

Country Name (2 letter code) [XX]:CN

State or Province Name (full name) []:HB

Locality Name (eg, city) [Default City]:WH

Organization Name (eg, company) [Default Company Ltd]:runtime

Organizational Unit Name (eg, section) []:runtime

Common Name (eg, your name or your server's hostname) []:runtime

Email Address []:

[root@DR CA]#

[root@DR CA]# touch index.txt && echo 01 > serial

3.RS生成证书签署请求，并发送给CA

#RS-1（httpd服务器）生成密钥

[root@RS-1 ssl]# (umask 077;openssl genrsa -out httpd.key 2048)

Generating RSA private key, 2048 bit long modulus

...................................................................................................................................................................................................................................................+++

................+++

e is 65537 (0x10001)

#RS-1（httpd服务器）生成证书签署请求

[root@RS-1 ~]# mkdir /etc/httpd/ssl

[root@RS-1 ~]# cd /etc/httpd/ssl

[root@RS-1 ssl]# openssl req -new -key httpd.key -days 1024 -out httpd.csr

You are about to be asked to enter information that will be incorporated

into your certificate request.

What you are about to enter is what is called a Distinguished Name or a DN.

There are quite a few fields but you can leave some blank

For some fields there will be a default value,

If you enter '.', the field will be left blank.

-----

Country Name (2 letter code) [XX]:CN

State or Province Name (full name) []:HB

Locality Name (eg, city) [Default City]:WH

Organization Name (eg, company) [Default Company Ltd]:runtime

Organizational Unit Name (eg, section) []:runtime

Common Name (eg, your name or your server's hostname) []:runtime

Email Address []:

Please enter the following 'extra' attributes

to be sent with your certificate request

A challenge password []:

An optional company name []:

[root@RS-1 ssl]#

[root@RS-1 ssl]# ls

httpd.csr  httpd.key

#把证书签署请求文件发送给CA

[root@RS-1 ssl]# scp httpd.csr root@192.168.32.125:/root

4.CA签署证书并发给客户端

[root@DR ~]# ls

anaconda-ks.cfg  httpd.csr

[root@DR ~]# openssl ca -in /root/httpd.csr -out httpd.crt -days 1024

Using configuration from /etc/pki/tls/openssl.cnf

Check that the request matches the signature

Signature ok

Certificate Details:

        Serial Number: 1 (0x1)

        Validity

            Not Before: Jul 24 15:27:28 2020 GMT

            Not After : May 14 15:27:28 2023 GMT

        Subject:

            countryName               = CN

            stateOrProvinceName       = HB

            organizationName          = runtime

            organizationalUnitName    = runtime

            commonName                = runtime

        X509v3 extensions:

            X509v3 Basic Constraints:

                CA:FALSE

            Netscape Comment:

                OpenSSL Generated Certificate

            X509v3 Subject Key Identifier:

                51:C2:11:E1:0D:86:FB:40:79:0B:F3:DD:5E:49:71:C6:D3:88:41:B1

            X509v3 Authority Key Identifier:

                keyid:31:D2:0A:8F:D2:DD:B9:3E:EE:05:B5:1B:58:C4:AF:8C:45:3B:C8:A0

Certificate is to be certified until May 14 15:27:28 2023 GMT (1024 days)

Sign the certificate? [y/n]:y

1 out of 1 certificate requests certified, commit? [y/n]y

Write out database with 1 new entries

Data Base Updated

[root@DR ~]# ls

anaconda-ks.cfg  httpd.crt  httpd.csr

#CA把签署好的证书httpd.crt和服务端的证书cacert.pem发给客户端

[root@DR ~]# scp httpd.crt root@192.168.32.130:/etc/httpd/ssl

[root@DR ~]# scp cacert.pem root@192.168.32.130:/etc/httpd/ssl

2.配置https

1.将RS-1的证书和密钥发给RS-2

[root@RS-2 ~]# yum -y install mod_ssl

[root@RS-2 ~]# mkdir /etc/httpd/ssl 

[root@RS-1 ~]# yum -y install mod_ssl

[root@RS-1 ssl]# ls

cacert.pem  httpd.crt  httpd.csr  httpd.key

[root@RS-1 ssl]# scp cacert.pem httpd.crt httpd.key root@192.168.32.135:/etc/httpd/ssl

root@192.168.32.135's password:

cacert.pem                                                       100% 1294     1.4MB/s   00:00

httpd.crt                                                        100% 4416     5.4MB/s   00:00

httpd.key   

#RS-2上查看

[root@RS-2 ~]# ls /etc/httpd/ssl/

cacert.pem  httpd.crt  httpd.key

2.修改https配置文件

[root@RS-1 ~]# vim /etc/httpd/conf.d/ssl.conf

//修改后如下所示

#   Server Certificate:

# Point SSLCertificateFile at a PEM encoded certificate.  If

# the certificate is encrypted, then you will be prompted for a

# pass phrase.  Note that a kill -HUP will prompt again.  A new

# certificate can be generated using the genkey(1) command.

SSLCertificateFile /etc/httpd/ssl/httpd.crt

#   Server Private Key:

#   If the key is not combined with the certificate, use this

#   directive to point at the key file.  Keep in mind that if

#   you've both a RSA and a DSA private key you can configure

#   both in parallel (to also allow the use of DSA ciphers, etc.)

SSLCertificateKeyFile /etc/httpd/ssl/httpd.key

#   Server Certificate Chain:

#   Point SSLCertificateChainFile at a file containing the

#   concatenation of PEM encoded CA certificates which form the

#   certificate chain for the server certificate. Alternatively

#   the referenced file can be the same as SSLCertificateFile

#   when the CA certificates are directly appended to the server

#   certificate for convinience.

#SSLCertificateChainFile /etc/pki/tls/certs/server-chain.crt

#   Certificate Authority (CA):

#   Set the CA certificate verification path where to find CA

#   certificates for client authentication or alternatively one

#   huge file containing all of them (file must be PEM encoded)

SSLCACertificateFile /etc/httpd/ssl/cacert.pem

#重启服务

[root@RS-1 ~]# systemctl restart httpd

[root@RS-1 ~]# ss -tanl

State       Recv-Q Send-Q    Local Address:Port                   Peer Address:Port

LISTEN      0      100           127.0.0.1:25                                *:*

LISTEN      0      128                   *:22                                *:*

LISTEN      0      100               [::1]:25                             [::]:*

LISTEN      0      128                [::]:443                            [::]:*

LISTEN      0      128                [::]:80                             [::]:*

LISTEN      0      128                [::]:22                             [::]:*

RS-2上也要做如上配置

3. LVS上配置规则

[root@DR ~]# ipvsadm -Ln

IP Virtual Server version 1.2.1 (size=4096)

Prot LocalAddress:Port Scheduler Flags

  -> RemoteAddress:Port           Forward Weight ActiveConn InActConn

TCP  192.168.32.250:80 rr

  -> 192.168.32.130:80            Masq    1      0          0

  -> 192.168.32.135:80            Masq    1      0          0

[root@DR ~]#

[root@DR ~]#

[root@DR ~]#

[root@DR ~]#

[root@DR ~]#

[root@DR ~]# ipvsadm -A -t 192.168.32.250:443 -s rr

[root@DR ~]# ipvsadm -a -t 192.168.32.250:443 -r 192.168.32.130 -m

[root@DR ~]# ipvsadm -a -t 192.168.32.250:443 -r 192.168.32.135 -m

[root@DR ~]#

[root@DR ~]#

[root@DR ~]#

[root@DR ~]#

[root@DR ~]# ipvsadm -Ln

IP Virtual Server version 1.2.1 (size=4096)

Prot LocalAddress:Port Scheduler Flags

  -> RemoteAddress:Port           Forward Weight ActiveConn InActConn

TCP  192.168.32.250:80 rr

  -> 192.168.32.130:80            Masq    1      0          0

  -> 192.168.32.135:80            Masq    1      0          0

TCP  192.168.32.250:443 rr

  -> 192.168.32.130:443           Masq    1      0          0

  -> 192.168.32.135:443           Masq    1      0          0

4. 客户端访问测试

curl 可以使用-k参数不验证证书的合法性



[root@localhost ~]#  for i in $(seq 10);do curl http://192.168.32.250;done

rs2

rs1

rs2

rs1

rs2

rs1

rs2

rs1

rs2

rs1

[root@localhost ~]#  for i in $(seq 10);do curl -k https://192.168.32.250;done

rs2

rs1

rs2

rs1

rs2

rs1

rs2

rs1

rs2

rs1

巴特西

LVS-DR：搭建HTTP和HTTPS负载均衡集群