Linux命令——ethtool
转自:https://www.cnblogs.com/kelamoyujuzhen/p/10116423.html
参考:9 Linux ethtool Examples to Manipulate Ethernet Card (NIC Card)
简介
ethtool允许你修改Ethernet adapter配置,并且这种修改只适用于physical ethernet adapters,这意味着bond0,tun0和任何其他非物理网络设备将无法与ethtool一起使用。
注意:大多数Linux内核将以太网设备标记为ethX,其中X是物理以太网接口的#(从0开始)。
我知道我知道,先从最少使用的东西开始。 但是,嘿,有人可能觉得这很有用,对吗? 在处理内核级别问题时,我可能不得不在10年以上查询驱动程序信息十几次,但有人必须在他们生命中的某个时刻遇到这个问题,让我告诉你,它可能更容易 运行一个命令,而不是通过lsmod挖掘并希望模块正确地拾取驱动程序。
驱动信息 和 统计数据
在处理内核级别的问题时,人们往往会使用lsmod来查看相应驱动是否被加载,使用ethtool可以更优雅的解决这个问题。
-i:Queries the specified network device for associated driver information.
root@ubuntu:~# ethtool -i ens32
driver: e1000
version: 7.3.21-k8-NAPI
firmware-version:
expansion-rom-version:
bus-info: 0000:02:00.0
supports-statistics: yes
supports-test: yes
supports-eeprom-access: yes
supports-register-dump: yes
supports-priv-flags: no
-S(大写):Queries the specified network device for NIC- and driver-spe‐cific statistics.
这个参数可以快速定位 rx/tx问题
root@ubuntu:~# ethtool -S ens32
NIC statistics:
rx_packets: 380
tx_packets: 386
rx_bytes: 42819
tx_bytes: 81789
rx_broadcast: 0
tx_broadcast: 0
rx_multicast: 0
tx_multicast: 0
rx_errors: 0
tx_errors: 0
tx_dropped: 0
multicast: 0
collisions: 0
rx_length_errors: 0
rx_over_errors: 0
rx_crc_errors: 0
rx_frame_errors: 0
rx_no_buffer_count: 0
rx_missed_errors: 0
tx_aborted_errors: 0
tx_carrier_errors: 0
tx_fifo_errors: 0
tx_heartbeat_errors: 0
tx_window_errors: 0
tx_abort_late_coll: 0
tx_deferred_ok: 0
tx_single_coll_ok: 0
tx_multi_coll_ok: 0
tx_timeout_count: 0
tx_restart_queue: 0
rx_long_length_errors: 0
rx_short_length_errors: 0
rx_align_errors: 0
tx_tcp_seg_good: 1
tx_tcp_seg_failed: 0
rx_flow_control_xon: 0
rx_flow_control_xoff: 0
tx_flow_control_xon: 0
tx_flow_control_xoff: 0
rx_long_byte_count: 42819
rx_csum_offload_good: 358
rx_csum_offload_errors: 0
alloc_rx_buff_failed: 0
tx_smbus: 0
rx_smbus: 0
dropped_smbus: 0
跟踪网卡
当一台服务器上有多张网卡,查找具体某一张物理网卡往往十分令人头疼。当然,你可以这么做:从ifconfig中取出MAC地址,将所有电缆插入一个管理型交换机,然后在交换机上将Mac表导出,查看具体Mac指向哪里。 使用ethtool可以更优雅地解决这个问题。
-p:Initiates adapter-specific action intended to enable an oper‐ator to easily identify the adapter by sight. Typically this involves blinking one or more LEDs on the specific network port.
ethtool -p ethX [N]
其中[N]是闪烁的秒数。 ethtool -p eth0 15使eth0闪烁15秒。此时,太网适配器背面的指示灯闪烁会闪烁。
测试Ethernet Adapter
可以针对物理以太网接口运行一些基本测试,测试有两个选项,一个online test(tests nvram and a link test)和一个offline test(register, memory, loopback, interrupt)。 脱机测试很可能在测试期间使主机离线,因此如果你对生产服务器或只能远程访问的计算机运行此操作,请特别注意。
ethtool -t ethX [offline|online]
root@ubuntu:~# ethtool -t ens32 online
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0 root@ubuntu:~# ethtool -t ens32 offline
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 13
Link test (on/offline) 0
一些网卡可能不支持online test 或者 offline test
改变Ethernet 配置
ethtool ethX
检查网卡配置信息
root@ubuntu:~# ethtool ens32
Settings for ens32:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
MDI-X: off (auto)
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000007 (7) drv probe link
Link detected: yes
可以得出结论:设备支持TP,最高1000BaseT/Full,自动协商。 Partner(Switch)支持最高100baseT / Full和自动协商。设备的实际设置:100Mb / s,全双工,运行TP,物理地址0,设置为自动协商,启用WoL并检测链路。
如果我网卡的支持链接模式设置为low(例如10/Half由于某种原因)但交换机支持1000baseT / Full,那么可以使用ethtool -s ethX将我的以太网设置更改为1000baseT / Full。几乎所有你看到的东西:ethtool ethX,可以用ethtool -s ethX改变。在这种情况下,您将使用以下内容:
ethtool -S eth0 speed 1000 duplex full autoneg on
-s(小写):Allows changing some or all settings of the specified network device. All following options only apply if -s was specified.
最新文章
- Ajax_04之jQuery中封装的Ajax函数
- springboot使用之四:错误页面404处理建议
- Oracle中的数据分页
- javaWeb加载Properties文件
- Struts2 从一个Action跳至另一个Action
- CSU 1111 D(Contest #3)
- UIKIT网页基本结构学习
- 基于CDH5.x 下面使用eclipse 操作hive 。使用java通过jdbc连接HIVESERVICE 创建表
- LNMPA by lin
- 【转】sed 的参数
- nginx 网络模型,cpu亲和等优点
- list标准函数的模拟
- pandas的基本功能(一)
- Java文件File类学习总结
- workerman——配置小程序的wss协议
- (转-经典-数据段)C++回顾之static用法总结、对象的存储,作用域与生存期
- POST 发送HTTP请求入参为:String url, Map<;String, Object>; propsMap
- Go linux 实践2
- WEBAPI 帖子收藏
- Oracle彻底删除11gR2 GI