Nexus：hardware type changed to No-Transceiver

如下是相关的案例：

1、N5K & Cat3750

较新版本的NX-OS在N5K上支持1G或10G，但N5K不支持auto-speed sensing

如下是故障信息的体现：3750和N5K之间安装GLC-SX-MM模块并连接，在3750上看了相关状态，出现了这个错误：

Description: Gi1/1/1: This port has been disabled because Non Compliant Gigabit Interface Converter (GBIC) connector detected.

（此端口已被禁用，因为检测到非兼容千兆位接口转换器（GBIC）连接器。）

Recommendation: Replace connector with cisco compliant Gigabit Interface Converter (GBIC) connector. Refer switch technical documentation to determine cisco compliant connector. Enable the port again.

（使用符合cisco标准的千兆位接口转换器（GBIC）连接器替换连接器。请参阅交换机技术文档以确定符合cisco的连接器。再次启用端口。）

操作如下：

①两个设备都支持GLC-SX-MM

②尝试shu/no shu接口

③Cat3750上体现的log：

*Apr  16 01:48:41.190: %PHY-4-SFP_NOT_SUPPORTED: The SFP in Gi1/1/1 is not supported

*Apr  16 01:48:41.190: %PM-4-ERR_DISABLE: gbic-invalid error detected on Gi1/1/1, putting Gi1/1/1 in err-disable state

④查看接口（支持GLC-SX-MM，接口下显示信息也OK）

3750_sw1#sh int gig 1/1/1 capa

GigabitEthernet1/1/1

  Model:                 WS-C3750X-48P

  Type:                  1000BaseSX SFP

  Speed:

  Duplex:                full

  Trunk encap. type:     802.1Q,ISL

  Trunk mode:            on,off,desirable,nonegotiate

  Channel:               yes

  Broadcast suppression: percentage(0-100)

  Flowcontrol:           rx-(off,on,desired),tx-(none)

  Fast Start:            yes

  QoS scheduling:        rx-(not configurable on per port basis),

                         tx-(4q3t) (3t: Two configurable values and one fixed.)

  CoS rewrite:           yes

  ToS rewrite:           yes

  UDLD:                  yes

  Inline power:          no

  SPAN:                  source/destination

  PortSecure:            yes

  Dot1x:                 yes

3750_sw1#

⑤但是3750的状态是not connect

3750_sw1#sh int gig 1/1/1 status

Port      Name               Status       Vlan       Duplex  Speed Type

Gi1/1/1                      notconnect   1            auto   auto 1000BaseSX SFP

3750_sw1#

⑥查看N5K上接口状态和信息：

N5K1# sh int e1/5 status

--------------------------------------------------------------------------------

Port          Name               Status    Vlan      Duplex  Speed   Type

--------------------------------------------------------------------------------

Eth1/5        --                 sfpInvali 1         full    10G     SFP-1000BAS

N5K1#

N5K1# sh int e1/5 capa

Ethernet1/5

  Model:                 N5K-C5548UP-SUP

  Type (SFP capable):    10Gbase-(unknown)

  Speed:                 1000,10000

  Duplex:                full

  Trunk encap. type:     802.1Q

  Channel:               yes

  Broadcast suppression: no

  Flowcontrol:           rx-(off/on),tx-(off/on)

  Rate mode:             none

  QOS scheduling:        rx-(6q1t),tx-(1p6q0t)

  CoS rewrite:           no

  ToS rewrite:           no

  SPAN:                  yes

  UDLD:                  yes

  Link Debounce:         yes

  Link Debounce Time:    yes

  MDIX:                  no

  Pvlan Trunk capable:   yes

  TDR capable:           no

  FabricPath capable:    yes

  Port mode:             Switched

  FEX Fabric:            yes

N5K1#

其实这里应该看到N5K和Cat3750之间的speed不匹配。

⑦查看N5K的log

N5K1#sh log | inc 1/5

...

2019 Apr 6 18:10:26 N5K1 %ETHPORT-5-IF_DOWN_NONE: Interface Ethernet1/5 is down (None)

...

2019 Apr 6 19:06:10 N5K1 %ETHPORT-5-IF_HARDWARE: Interface Ethernet1/5, hardware type changed to No-Transceiver

⑧在N5K手动设置速度

N5K1# sh int e1/5 stat

--------------------------------------------------------------------------------

Port          Name               Status    Vlan      Duplex  Speed   Type

--------------------------------------------------------------------------------

Eth1/5        --                 connected 1         full         SFP-1000BAS

N5K1#

可以看到修改后正常了。

Summary: The newer versions of NX-OS support 1G or 10G on the N5K, but the N5K is not auto-speed sensing. If you run into something similar, even error messages on the remote device, check the port speed on the N5K.

2、N5600 & FEX 2248PQ

巴特西

Nexus：hardware type changed to No-Transceiver

最新文章

热门文章