STM32串口DMA接收数据错位—

背景：两片STM32通过串口通信，为了减小CPU负担，采用DMA进行通信，发送端为STM32F103C8T6，接收端为STM32F407VET6。在调试的过程中发现，一直出现数据错位的问题，接收端尝试了串口空闲中断和串口DMA传输完成中断，错位问题依旧，其实我之前遇到过这个问题，那次发送端没有使用DMA，而是直接用串口发送，接收端采用DMA接收完成中断，检测到错位后，延时重置DMA，直到DMA接收同步后，不再重置，此后DMA便会保持同步，不会错位。但是这次不知道为什么采用上次的方法没有解决，因此决定直接用最简单粗暴的方法——查找，但是弊端是会在中断中运行一段比较占空时间的代码。

说明：主要部分在接收中断（本文最后的代码段），发送端发送的DMA数据长度为a，接收端DMA配置的BufferSize为2a，这样即使错位，在2a的数据长度中也一定会存在一段完整的有效数据。接收中断中，在接收buffer的前半段查找帧头，找到之后，判断帧头+a-1的位置是否是帧尾，如果是，则基本可以认为中间即为有效数据，将该段数据拷贝到一个新的数组中，等待解析。

配置部分：发送端 STM32F103C8T6

/* uart3 for communicate with the master */

void vUart3Config(void)

{

        GPIO_InitTypeDef 	GPIO_InitStructure;

	USART_InitTypeDef       USART_InitStructure;

	NVIC_InitTypeDef 	NVIC_InitStructure;

	DMA_InitTypeDef		DMA_InitStructure;

	RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);

	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);

	RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);

	/* USART3_RX	  GPIOB.11 */

        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;

        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

        GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;

        GPIO_Init(GPIOB, &GPIO_InitStructure);  

	/* USART3_TX   GPIOB.10 */

        GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;

        GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

        GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;

        GPIO_Init(GPIOB, &GPIO_InitStructure);

	NVIC_InitStructure.NVIC_IRQChannel = USART3_IRQn;

	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 3;

	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;

	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;

	NVIC_Init(&NVIC_InitStructure);

	USART_InitStructure.USART_BaudRate = 115200;

	USART_InitStructure.USART_WordLength = USART_WordLength_8b;

	USART_InitStructure.USART_StopBits = USART_StopBits_1;

	USART_InitStructure.USART_Parity = USART_Parity_No;

	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;

	USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;

        USART_Init(USART3, &USART_InitStructure);

        USART_Cmd(USART3, ENABLE);

        USART_ITConfig(USART3, USART_IT_RXNE, ENABLE);

	{ /* send dma */

		USART_DMACmd(USART3,USART_DMAReq_Tx,ENABLE);

		DMA_DeInit(DMA1_Channel2);

		DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)(&(USART3->DR));

		DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)SendToMaster_Buff;

		DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;

		DMA_InitStructure.DMA_BufferSize = USART3_DMA_send_buffersize;

		DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;

		DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;

		DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;

		DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;

		DMA_InitStructure.DMA_Mode = DMA_Mode_Circular;

		DMA_InitStructure.DMA_Priority = DMA_Priority_VeryHigh;

		DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;

		DMA_Init(DMA1_Channel2,&DMA_InitStructure);

		NVIC_InitStructure.NVIC_IRQChannel = DMA1_Channel2_IRQn;

		NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;

		NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;

		NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;

		NVIC_Init(&NVIC_InitStructure);

		DMA_ITConfig(DMA1_Channel2,DMA_IT_TC,ENABLE);

		DMA_Cmd(DMA1_Channel2,ENABLE);

	}

}

配置部分：接收端 STM32F407VET6

void vUTConfig(void)

{

	USART_InitTypeDef usart;

	GPIO_InitTypeDef  gpio;

	NVIC_InitTypeDef  nvic;

	DMA_InitTypeDef   dma;

	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA,ENABLE);

	RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1,ENABLE);

	RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_DMA2, ENABLE);

	GPIO_PinAFConfig(GPIOA,GPIO_PinSource9 ,GPIO_AF_USART1);

	GPIO_PinAFConfig(GPIOA,GPIO_PinSource10,GPIO_AF_USART1); 

	/* USART1_RX	  GPIOA.10 */

	gpio.GPIO_Pin = GPIO_Pin_9|GPIO_Pin_10;

	gpio.GPIO_Mode = GPIO_Mode_AF;

	gpio.GPIO_OType = GPIO_OType_PP;

	gpio.GPIO_Speed = GPIO_Speed_100MHz;

	gpio.GPIO_PuPd = GPIO_PuPd_NOPULL;

	GPIO_Init(GPIOA,&gpio);

	usart.USART_BaudRate = 115200;

	usart.USART_WordLength = USART_WordLength_8b;

	usart.USART_StopBits = USART_StopBits_1;

	usart.USART_Parity = USART_Parity_No;

	usart.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;

	usart.USART_HardwareFlowControl = USART_HardwareFlowControl_None;

	USART_Init(USART1,&usart);

	USART_Cmd(USART1,ENABLE);

	{ /* receive dma */

		USART_DMACmd(USART1,USART_DMAReq_Rx,ENABLE);

		DMA_DeInit(DMA2_Stream2);

		dma.DMA_Channel= DMA_Channel_4;

		dma.DMA_PeripheralBaseAddr = (uint32_t)&(USART1->DR);

		dma.DMA_Memory0BaseAddr = (uint32_t)ReceiveFromUT_Buffer;

		dma.DMA_DIR = DMA_DIR_PeripheralToMemory;

		dma.DMA_BufferSize = USART1_UT_DMA_receive_buffersize;

		dma.DMA_PeripheralInc = DMA_PeripheralInc_Disable;

		dma.DMA_MemoryInc = DMA_MemoryInc_Enable;

		dma.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;

		dma.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;

		dma.DMA_Mode = DMA_Mode_Circular;

		dma.DMA_Priority = DMA_Priority_VeryHigh;

		dma.DMA_FIFOMode = DMA_FIFOMode_Disable;

		dma.DMA_FIFOThreshold = DMA_FIFOThreshold_1QuarterFull;

		dma.DMA_MemoryBurst = DMA_MemoryBurst_Single;

		dma.DMA_PeripheralBurst = DMA_PeripheralBurst_Single;

		DMA_Init(DMA2_Stream2,&dma);

		nvic.NVIC_IRQChannel = DMA2_Stream2_IRQn;

		nvic.NVIC_IRQChannelPreemptionPriority = 1;

		nvic.NVIC_IRQChannelSubPriority = 1;

		nvic.NVIC_IRQChannelCmd = ENABLE;

		NVIC_Init(&nvic);

		DMA_ITConfig(DMA2_Stream2,DMA_IT_TC,ENABLE);

		DMA_Cmd(DMA2_Stream2,ENABLE);

	}

}

中断部分：发送中断

/* USART3 DMA send interrupt */

void DMA1_Channel2_IRQHandler(void)

{

	if(DMA_GetITStatus(DMA1_IT_TC2))

	{

		DMA_ClearFlag(DMA1_IT_TC2);

		DMA_ClearITPendingBit(DMA1_IT_TC2);

//		DMA_Cmd(DMA1_Channel2,DISABLE);

//		DMA_SetCurrDataCounter(DMA1_Channel2,USART3_DMA_send_buffersize);

//		DMA_Cmd(DMA1_Channel2, ENABLE);

	}

}

中断部分：接收中断

/* USART1 dma receive for ut */

void DMA2_Stream2_IRQHandler(void)

{

	uint8_t i = 0;

	if(DMA_GetFlagStatus(DMA2_Stream2,DMA_IT_TCIF2) == SET)

	{

		/* 在前半部分查找帧头并校验对应位置是否为帧尾 */

		for(i=0;i<(USART1_UT_DMA_receive_buffersize/2);i++)

		{

			if((ReceiveFromUT_Buffer[i] == 0x05)&&(ReceiveFromUT_Buffer[i+USART1_UT_DMA_receive_buffersize-1] == 0x06))

			{

				/* 拷贝有效数据段到待解析数组 */

				memcpy(ReceiveFromUT_Data,&ReceiveFromUT_Buffer[i],USART1_UT_DMA_receive_buffersize/2);

				/* 数据解析 */

				UTReceive();

			}

		}

		/* 没有有效数据 */

		if(i >= USART1_UT_DMA_receive_buffersize/2)

		{

			/* 重置DMA */

			DMA_Cmd(DMA2_Stream2,DISABLE);

			DMA_SetCurrDataCounter(DMA2_Stream2,USART1_UT_DMA_receive_buffersize);

			DMA_Cmd(DMA2_Stream2,ENABLE);

		}

		DMA_ClearFlag(DMA2_Stream2, DMA_FLAG_TCIF2);

		DMA_ClearITPendingBit(DMA2_Stream2, DMA_IT_TCIF2);

	}

}

——cloudos

——2020/4/17

巴特西

STM32串口DMA接收数据错位——暴力解决方法

最新文章

热门文章