目录

无Vlan的VRRP

有Vlan的VRRP

今天要讲的VRRP都是基于路由器的VRRP。

一：无Vlan的VRRP

如图，PC1和PC2是企业内网主机，AR1和AR2是企业访问外网的路由器，有一个默认路由指向AR3。AR1和AR2之间形成第一跳网关冗余。PC1通过AR1以NAT方式访问外网，PC2通过AR2以NAT方式访问外网。AR1、AR2之间任何一个路由器宕机都不影响PC1和PC2访问外网。AR1、AR2、AR3之间运行OSPF协议。

技术要点：AR1和AR2的g0/0/0接口配置两个ip地址，再结合VRRP技术

PC1

PC>ipconfig

IPv4 address......................: 192.168.10.10

Subnet mask.......................: 255.255.255.0

Gateway...........................: 192.168.10.254

Physical address..................: 54-89-98-8E-41-17

PC2

PC>ipconfig

IPv4 address......................: 192.168.10.10

Subnet mask.......................: 255.255.255.0

Gateway...........................: 192.168.10.254

Physical address..................: 54-89-98-8E-41-17

AR1

[AR1]display current-configuration

#

acl number 2000                             //匹配需要NAT的网段

 rule 5 permit source 192.168.10.0 0.0.0.255

 rule 10 permit source 192.168.20.0 0.0.0.255

#

interface GigabitEthernet0/0/0

 ip address 192.168.10.1 255.255.255.0

 ip address 192.168.20.1 255.255.255.0 sub       //一个接口配两个地址

 vrrp vrid 10 virtual-ip 192.168.10.254

 vrrp vrid 10 priority 150                       //设置优先级

 vrrp vrid 10 preempt-mode timer delay 10        //抢占时间10秒

 vrrp vrid 10 track interface GigabitEthernet0/0/1 reduced 60 //端口状态监测

 vrrp vrid 10 authentication-mode md5 %$%$7_&c4,7Hl+O8!oBync[2o~1,%$%$  //认证

 vrrp vrid 20 virtual-ip 192.168.20.254

 vrrp vrid 20 authentication-mode md5 %$%$l,rF;gtS<J9zB}O1H:CMo~dG%$%$

#

interface GigabitEthernet0/0/1

 ip address 13.1.1.1 255.255.255.0

 nat outbound 2000                               // NAT

#

ospf 100 router-id 13.1.1.1

 area 0.0.0.0

  network 13.1.1.1 0.0.0.0

#

ip route-static 0.0.0.0 0.0.0.0 13.1.1.3

#

AR2

[AR2]display current-configuration

#

acl number 2000

 rule 5 permit source 192.168.10.0 0.0.0.255

 rule 10 permit source 192.168.20.0 0.0.0.255

#

interface GigabitEthernet0/0/0

 ip address 192.168.10.2 255.255.255.0

 ip address 192.168.20.2 255.255.255.0 sub

 vrrp vrid 10 virtual-ip 192.168.10.254

 vrrp vrid 10 authentication-mode md5 %$%$RcPz'1Xr;Gj1#=~x*hC5o@SW%$%$

 vrrp vrid 20 virtual-ip 192.168.20.254

 vrrp vrid 20 priority 150

 vrrp vrid 20 preempt-mode timer delay 10

 vrrp vrid 20 track interface GigabitEthernet0/0/1 reduced 60

 vrrp vrid 20 authentication-mode md5 %$%$~B9v,^2%6KSZB4@WB#DTo@NI%$%$

#

interface GigabitEthernet0/0/1

 ip address 23.1.1.2 255.255.255.0

 nat outbound 2000

#

ospf 100 router-id 23.1.1.2

 area 0.0.0.0

  network 23.1.1.2 0.0.0.0

#

ip route-static 0.0.0.0 0.0.0.0 23.1.1.3

#

AR3

[AR3]display current-configuration

#

interface GigabitEthernet0/0/0

 ip address 13.1.1.3 255.255.255.0

#

interface GigabitEthernet0/0/1

 ip address 23.1.1.3 255.255.255.0

#

ospf 100 router-id 33.3.3.3

 area 0.0.0.0

  network 13.1.1.3 0.0.0.0

  network 23.1.1.3 0.0.0.0

#

有Vlan的VRRP

如图，PC1和PC2是企业内网主机，分别属于Vlan10和Vlan20，AR1和AR2是企业访问外网的路由器，有一个默认路由指向AR3。AR1和AR2之间形成第一跳网关冗余。PC1通过AR1以NAT方式访问外网，PC2通过AR2以NAT方式访问外网。AR1、AR2之间任何一个路由器宕机都不影响PC1和PC2访问外网。AR1、AR2、AR3之间运行OSPF协议。

技术要点：AR1和AR2配置虚拟地址，再结合VRRP技术

PC1

PC>ipconfig

IPv4 address......................: 192.168.10.10

Subnet mask.......................: 255.255.255.0

Gateway...........................: 192.168.10.254

Physical address..................: 54-89-98-8E-41-17

Vlan..............................: 10

PC2

PC>ipconfig

IPv4 address......................: 192.168.10.10

Subnet mask.......................: 255.255.255.0

Gateway...........................: 192.168.10.254

Physical address..................: 54-89-98-8E-41-17

Vlan..............................: 20

LSW1

[LSW1]display current-configuration

#

vlan batch 10 20

#

interface GigabitEthernet0/0/1

 port link-type trunk

 port trunk allow-pass vlan 10 20

#

interface GigabitEthernet0/0/2

 port link-type trunk

 port trunk allow-pass vlan 10 20

#

interface GigabitEthernet0/0/3

 port link-type access

 port default vlan 10

#

interface GigabitEthernet0/0/4

 port link-type access

 port default vlan 20

#

AR1

[AR1]display current-configuration

#

acl number 2000

 rule 5 permit source 192.168.10.0 0.0.0.255

 rule 10 permit source 192.168.20.0 0.0.0.255

#

interface GigabitEthernet0/0/0.10

 dot1q termination vid 10                         //使虚拟接口能识别Vlan10

 ip address 192.168.10.1 255.255.255.0

 vrrp vrid 10 virtual-ip 192.168.10.254

 vrrp vrid 10 priority 150

 vrrp vrid 10 preempt-mode timer delay 10

 vrrp vrid 10 track interface GigabitEthernet0/0/1 reduced 60

 vrrp vrid 10 authentication-mode md5 %$%$}'&x<I!T>,WFD'08G=yToU,o%$%$

 arp broadcast enable                            //虚拟接口恩给你发送arp广播

#

interface GigabitEthernet0/0/0.20

 dot1q termination vid 20                        //使虚拟接口能识别Vlan20

 ip address 192.168.20.1 255.255.255.0

 vrrp vrid 20 virtual-ip 192.168.20.254

 vrrp vrid 20 authentication-mode md5 %$%$<w9#Ez1k!~Y3+},DQtjGoUQ^%$%$

 arp broadcast enable

#

interface GigabitEthernet0/0/1

 ip address 13.1.1.1 255.255.255.0

 nat outbound 2000

#

ospf 100 router-id 13.1.1.1

 area 0.0.0.0

  network 13.1.1.1 0.0.0.0

#

ip route-static 0.0.0.0 0.0.0.0 13.1.1.3

#

AR2

[V200R003C00]

#

acl number 2000

 rule 5 permit source 192.168.10.0 0.0.0.255

 rule 10 permit source 192.168.20.0 0.0.0.255

#

interface GigabitEthernet0/0/0.10

 dot1q termination vid 10

 ip address 192.168.10.2 255.255.255.0

 vrrp vrid 10 virtual-ip 192.168.10.254

 vrrp vrid 10 authentication-mode md5 %$%$ei}p>OY2kXEOij8TquxQoV*0%$%$

 arp broadcast enable

#

interface GigabitEthernet0/0/0.20

 dot1q termination vid 20

 ip address 192.168.20.2 255.255.255.0

 vrrp vrid 20 virtual-ip 192.168.20.254

 vrrp vrid 20 priority 150

 vrrp vrid 20 preempt-mode timer delay 10

 vrrp vrid 20 track interface GigabitEthernet0/0/1 reduced 60

 vrrp vrid 20 authentication-mode md5 %$%$&G-7Us\hbQxS@vFhpdoRoV"8%$%$

 arp broadcast enable

#

interface GigabitEthernet0/0/1

 ip address 23.1.1.2 255.255.255.0

 nat outbound 2000

#

ospf 100 router-id 23.1.1.2

 area 0.0.0.0

  network 23.1.1.2 0.0.0.0

#

ip route-static 0.0.0.0 0.0.0.0 23.1.1.3

#

AR3

[AR3]display current-configuration

#

interface GigabitEthernet0/0/0

 ip address 13.1.1.3 255.255.255.0

#

interface GigabitEthernet0/0/1

 ip address 23.1.1.3 255.255.255.0

#

ospf 100 router-id 33.3.3.3

 area 0.0.0.0

  network 13.1.1.3 0.0.0.0

  network 23.1.1.3 0.0.0.0

#

附上存在Vlan时的ensp源文件：链接: https://pan.baidu.com/s/1S5xzALnyg8cmn_lTB_jd_w 密码: yez5

基于防火墙的VRRP--------------->基于防火墙的VRRP技术--华为防火墙双击热备----VGMP

基于三层交换机的VRRP -------->基于三层交换机的VRRP技术--MSTP、VRRP的综合运用

最新文章

  1. Ajax工作流程
  2. Java基础-字面值
  3. [OpenCV]（1）安装与测试
  4. PL/SQL — 存储过程
  5. 30、ADO.NET、事务、DataSet
  6. Android之Intent
  7. 类型 - PHP手册笔记
  8. ArrayList的sublist注意
  9. 浅谈JavaScript递归
  10. android studio 怎么将项目打包成apk文件
  11. python对字符串分割和截取的方法
  12. HashMap 的底层原理
  13. java中包的定义
  14. mysql 导入数据库问题
  15. JS_高程5.引用类型（6）Array类型的位置方法，迭代方法，归并方法
  16. EF Core
  17. 使用paramiko远程登录并执行命令脚本
  18. Fiddler 手机抓包介绍
  19. WPF 我的初学必备技能
  20. 【原创】kerberos无密码登录

热门文章

  1. Learn Python the Hard Way，ex37-1
  2. 我与FreeBSD的故事之一
  3. Apache配置 7.静态元素过期时间
  4. 【odoo14】第十八章、自动化测试
  5. Solon 框架详解（十一）- Solon Cloud 的配置说明
  6. 记一次scrapy-redis爬取小说网的分布式搭建过程
  7. JavaWeb开发中的分层思想（一）
  8. 攻防世界 reverse tt3441810
  9. 浅析MyBatis（四）：全自动写代码的MyBatis逆向工程
  10. Python爬虫系列之爬取美团美食板块商家数据（二）