64位系统安装目录分为两种

64位用：C:\Program Files

32位用：C:\Program Files (x86)

64位系统系统目录分为两种

64位用：C:\Windows\System32

32位用：C:\Windows\SysWOW64

64位系统注册表分为两种

64位用：[HKEY_LOCAL_MACHINE\SOFTWARE]

32位用：[HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node]

所以在64位系统中运行32位的DLL，应将DLL放在C:\Windows\SysWOW64目录下，写注册表应该是[HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node]下，调用的程序应该在C:\Program Files (x86)下。注册表中的键值应该指向的是C:\Windows\SysWOW64下

> dumpbin /headers tvicport.dll

Microsoft (R) COFF/PE Dumper Version 14.13.26131.1

Copyright (C) Microsoft Corporation.  All rights reserved.

Dump of file tvicport.dll

PE signature found

File Type: DLL

FILE HEADER VALUES

             14C machine (x86)

               5 number of sections

        424A6D4E time date stamp Wed Mar 30 17:11:42 2005

               0 file pointer to symbol table

               0 number of symbols

              E0 size of optional header

            210E characteristics

                   Executable

                   Line numbers stripped

                   Symbols stripped

                   32 bit word machine

                   DLL

......

> dumpbin /headers tvicport.sys

Microsoft (R) COFF/PE Dumper Version 14.13.26131.1

Copyright (C) Microsoft Corporation.  All rights reserved.

Dump of file tvicport.sys

PE signature found

File Type: EXECUTABLE IMAGE

FILE HEADER VALUES

             14C machine (x86)

               8 number of sections

        424A6D84 time date stamp Wed Mar 30 17:12:36 2005

               0 file pointer to symbol table

               0 number of symbols

              E0 size of optional header

             30E characteristics

                   Executable

                   Line numbers stripped

                   Symbols stripped

                   32 bit word machine

                   Debug information stripped

......

@copy TVicPort.sys %WINDIR%\SysWOW64\drivers /y

@copy TVicPort64.sys %WINDIR%\System32\drivers /y

@copy TVicPort.dll %WINDIR%\System /y

TASKKILL /F /IM tpfcicon.exe

TASKKILL /F /IM tpfcicon_noballons.exe

TASKKILL /F /IM TPFanControl.exe

net stop TPFanControl

TPFanControl -u

//NEW: Set UseTWR=1 to see more sensors, will work only on newer T4xx

// ATTENTION: if only one (cpu) sensor is displayed, TWR is not

// working properly, displayed temp is faulty, go back to UseTWR=0

// 新：设置usetwr=1以查看更多传感器，仅适用于较新的t4xx

// 注意：如果只显示一个（CPU）传感器，则twr不显示

// 工作正常，显示温度有问题，返回使用twr=0

// Notice: Only Support TPFC v0.63 Setting

UseTWR=0

//--------------------------------------------------------------------

//

// >>>>  Celsius / Fahrenheit: temperatures in degree Celsius(active) / Fahrenheit  <<<<

// !!!! "Level" FAN 0 > 80 -> switch to Fahrenheit !!!! see below

// 最低一级的温度值如果>80的话,则温度自动识别为华氏度.

// ATTENTION: example temp values are for my T61, especially

// BluetoothEDR=1,  SensorName5=no5, IgnoreSensors=no5 too

// temp levels 10 degrees centgrade higher than in T4x, R5x,

// change for your purposes.

// 注意,下面的温度设置是以我的T61为例,特别是蓝牙EDR设置为1,第五个传感器名称改为no5,并且忽略这个传感器的温度显示.在T4X,R5X机器上,温度设置要高个10°,总之以你自己实测的效果来调试.

// advice for programmers: TPFanControl must acquire mutex named

// "Access_Thinkpad_EC" to get access to embedded controller

// 建议: TPFanControl必须获得"Access_Thinkpad_EC"才能得到温度值.

// with Active=3 & ManFanSpeed=0 & ManModeExit=78 you can have a nice

// quiet time until temps reaches 78 deg. centigrade  :-))

// 当使用手动模式(Active=3),风速为0(ManFanSpeed=0),并且将"手动切换到智能的温度阀值"设定为78°(ManModeExit=78)的话,你的电脑将会异常安静,除非温度攀升到78°.

// -----------------------------------------------------------------

// -----------------------------------------------------------------

// "Active=0" program just reads config.  程序仅读取配置

// "Active=1" allow program to modify fan.  允许程序修改风速

// "Active=2" program will come up in smart mode.  程序以智能模式启动

// "Active=3" program will come up in manual mode.  程序以手动模式启动

Active=1

// -----------------------------------------------------------------

// manual fan speed at program start

// 程序启动时,手动风速的初始值.(*我发现我的T61上,64风速是最快的*)

ManFanSpeed=7

// -----------------------------------------------------------------

// Program exits manual mode and switches to smart mode with last chosen

// profile, if this temp (degrees Centigrade or Fahrenheit) is achieved.

// default= 80 degrees Centigrade / 176 degrees Fahrenheit.

// 当温度达到该值时,程序将自动退出手动模式,并切换到之前启用过的智能模式.

//ManModeExit=55     //ManModeExit=131   // with Fahrenheit

ManModeExit=55 

// -----------------------------------------------------------------

// Window stays on Top if StayOnTop=1, normal behavior =0

// 窗口是否一直前置显示,1为前置,默认为0,不前置.

StayOnTop=0

// -----------------------------------------------------------------

// Set to 1 for slim widget

// 1为窗口细长型显示,0为窗口粗矮型显示,显示的信息量相应的多一些.

SlimDialog=1   

// -----------------------------------------------------------------

// set to 1 for bluetooth with enhanced data rate (i.e. T61,

// X61  for T4x, R5x set BluetoothEDR=0 )

// 设置为1时增强蓝牙的传输速率,例如T61,X61.但是对于T4x,R5x,请设置为0

BluetoothEDR=1

// -----------------------------------------------------------------

// Windows Priority of Process (0-5, normal=2), increase if fancontrol has

// big delays in response while other processes consume performance.

// 程序的优先级,可以设定为0-5,正常是2,如果其他程序大量消耗系统资源导致TPFanControl有较大的延迟,请把这个数值加大.

ProcessPriority=5

// -----------------------------------------------------------------

// Show no icon ballons: NoBallons=1, show icon ballons: NoBallons=0

// 禁止托盘处的程序图标显示提示信息时,设为1,反之设为0.

NoBallons=1

// -----------------------------------------------------------------

// check temperatures every x seconds (default 5)

// 每隔x秒检查温度,默认是5.

Cycle=1

// -----------------------------------------------------------------

// For Thinkpads A2x,T2x,X2x set NoExtSensor=1 to exclude reading

// of extended sensors to prevent program errors. Attention 570(E)

// is NOT compatible. Fan speed is not available on all models.

// 对于Thinkpad A2x,T2x,X2x,设为1可以避免因读取不存在的温度传感器而导致程序出错.注意,570(E)是不兼容的.所有的机型上都无法设定风速.

NoExtSensor=0

// -----------------------------------------------------------------

// Minimize to systray immediately when starting

// 设定为1时,当程序启动后,立即最小化到托盘.

StartMinimized=1

// -----------------------------------------------------------------

// check icon of tpfcicon.exe (optional) every x seconds (default 1)

// 每x秒检查tpfcicon.exe的图标(可选,默认是1秒).

IconCycle=1

// -----------------------------------------------------------------

// Show new icon with max. temperature / sensor name

// 显示最高的温度和芯片的名称

ShowTempIcon=1

// -----------------------------------------------------------------

// Save the icon by a start delay of the program/service of

// "SecStartDelay" (sec.) within "SecWinUptime" (sec.) after (re)boot

// Delete slashes '//' at next 3 parameters.

// 在启动或重启后,设定程序的延时启动时间,将下面的'//'删掉就能启用(*这个没啥用,我不弄的*)

//

//SecWinUptime=120	//"SecWinUptime" (sec.) after (re)boot

//SecStartDelay=60	//start delay of the program (sec.)

//NoWaitMessage=0	//set to 1 to avoid sleep message

// Notice: Only Support TPFC v0.63 Setting

//ReIcCycle=600		//rebuild TempIcon every xxx secs.

// -----------------------------------------------------------------

// Temperature thresholds for turning the taskbar icon

// yellow orange red (Smart and Manual mode only and

// only together with MinimizeToTray=1)

// 对于不同的温度,系统托盘所显示的颜色,黄,橙,红.仅在智能和手动模式下生效,并且MinimizeToTray=1

//IconLevels=65 75 80    // Fahrenheit: IconLevels=122 140 158

IconLevels=50 60 65 

// -----------------------------------------------------------------

// Beep frequency and duration (in ms) for successful

// fan state changes. (Set either or both to zero to

// disable)

// 当成功转换风扇状态时,蜂鸣器的频率和时长(毫秒),任何一个值设定为0时,禁止蜂鸣.

FanBeep=0 0

// --------------------------------------------------------

// If this max number of consecutive EC read errors occur

// program will switch fan back to bios mode and exit

// 当读取温度传感器的错误次数达到改设定值后,程序将自动切换到bios控制并退出.

MaxReadErrors= 10

// --------------------------------------------------------

// Log2File=1 enables, Log2File=0 disables writing to TPFanControl.log

// Start program with admin rights.

// 允许或禁止写入日志文件,这个需要管理员权限

Log2File=0

// --------------------------------------------------------

// Log2csv=1 enables, Log2csv=0 disables

// writing to TPFanControl_csv.txt renamed to

// TPFanControl_last_csv.txt after restart of TPFanControl

// rename to *.csv for use with excel

// Start program with admin rights.

// 设定为1时,允许日志写入TPFanControl_csv.txt,程序重启后,自动更名为TPFanControl_last_csv.txt.将扩展名改成.csv时,可以用excel打开.(*这个需要在文件夹选项中,将"隐藏已知类型的扩展名"后面的勾去掉才能显示并更改扩展名*)

Log2csv=0

// --------------------------------------------------------

// List (separated by comma) of sensors to ignore when

// determining the max. temperature.  (Use lower case,

// e.g "IgnoreSensors=pci,aps")

// 判断最高温度时,哪些芯片是不受监控的(相当于黑名单,多个名称用逗号隔开,并用小写字母).

IgnoreSensors=aps,crd,bat,bus,pci,pwr

// (*我的T61有显卡门,所以只监控gpu的温度,除了gpu,其他所有的芯片都列上去了.大家可以把cpu从黑名单中删除*)

// ---------------------------------------------------------

// List of new 3 letter sensor names, delete leading

// slashes to activate. Don't use capital letters for readability

// of temp icon.

// 写3个新的字母来重新命名芯片的名称,把'//'删除就能启用.别用大写字母

//SensorName1=cpu

//SensorName2=aps

//SensorName3=pcm

//SensorName4=gpu

//SensorName5=no5

//SensorName6=x7d

//SensorName7=bat

//SensorName8=x7f

//SensorName9=bus

//SensorName10=pci

//SensorName11=pwr

//SensorName12=xc3

// ---------------------------------------------------------

// calculating Highest Temp with:

// temperature of sensor no. = real temp minus SensorOffsetno.

// Default SensorOffset1-12=0 , Capital O in SensorOffset,

// to activate delete slashes '//',

// Negative SensorOffsetno. values increase temperature values.

// 重新计算最高温度,传感器温度=实测温度-偏移量,默认的偏移量都为0,删除'//'可以启用计算.当偏移量为负数时,则增大温度值

//SensorOffset1=20

//SensorOffset2=20

//SensorOffset3=0

//SensorOffset4=2

//SensorOffset5=1

//SensorOffset6=5

//SensorOffset7=5

//SensorOffset8=4

//SensorOffset9=3

//SensorOffset10=2

//SensorOffset11=1

//SensorOffset12=5

// -----------------------------------------------------------------

// set to 1 to show calculated temps for sensors

// 设定为1时,显示计算后的温度值

ShowBiasedTemps=1 

// -----------------------------------------------------------------

// Show all/active sensors at start up. all=1 only active=0

// 在启动时,显示所有/激活的传感器温度值,1为所有,0为激活的

ShowAll=0 

// --------------------------------------------------------

// temperature levels 'Level=' with associated fan levels

// (for the fan to come back, temperature must fall

// down to previous level).  There may be more or

// less levels in this list.  The first one should

// have a fan speed of zero and is the "turn off"

// temperature.

// Fan speed of 64 is extreme and may be an *unsupported*

// and *damaging* mode.  A fan speed of 128 setting is

// not really a fan speed in itself but will instead switch

// fan control to BIOS mode (0x80).  The idea of this

// is to let the program get out of the way and let the

// BIOS handle extremes.(and then switch back to smart if

// the temperature is okay again)

// Temp of lowest Level (commonly set to fan speed zero) of profile

// "Smart Mode 1" will switch from Celsius to Fahrenheit if set higher

// than 79 degrees. Temps of higher levels have no influence on F/C.

//

// profile "Smart Mode 1"

// Celsius:         	// Fahrenheit: 

// change values and number of items for your needs

// !!!! "Level" FAN 0 > 80 -> switch to Fahrenheit !!!!

// Notice: Only Support TPFC v0.63 Setting

MenuLabelSM1=Smart Mode 1/  Label for Icon Menu, must be terminated by '/'

// (*智能模式1下的设定*)

//

//Level=60 0		// Level=140 0

//Level=65 1		// Level=150 1

//Level=75 3		// Level=165 3

//Level=80 7		// Level=175 7

//Level=90 64		// Level=195 64

Level=30 0

Level=40 1

Level=45 4

Level=49 7

Level=52 64

// (*这些是我的温度设定,分别设定了30°,40°,45°,49°,52°,可以自己改*)

// optional 2nd profile "Smart Mode 2", switched by icon menue

// change values and number of items for your needs

// to deactivate, insert leading '//' into following lines

// Notice: Only Support TPFC v0.63 Setting

MenuLabelSM2=Smart Mode 2/  Label for Icon Menu, must be terminated by '/'

// (*智能模式2下的设定*)

//

//Level2=22 0		// Level2=70 0

//Level2=33 1		// Level2=90 1

//Level2=38 2		// Level2=100 2

//Level2=44 3		// Level2=110 3

//Level2=55 7		// Level2=130 7

//Level2=66 64		// Level2=150 64

//Level2=77 128		// Level2=170 128

Level2=30 0

Level2=40 1

Level2=45 4

Level2=49 7

Level2=52 64

// (*这些是我的温度设定,分别设定了30°,40°,45°,49°,52°,可以自己改*)

// -----------------------------------------------------------------

// IconColorFan=1 digital Icon will turn green while fan is running.

// 设定为1时,当风扇转的时候,图标为绿色

IconColorFan=1

// -----------------------------------------------------------------

// Lev64Norm=1 : Fan level 64 acts as normal level with hysteresis,

// fan will run till next lower temp step is reached (no pulsing fan).

// If set to zero fan level 64 acts as emergency level without hysteresis,

// fan will run till level64 temp is reached again (pulsing fan can happen).

// 设定为1时,最高风速有延迟效应,也就是说,当温度下降到最高档温度值以下时,风速仍旧为最高,直到继续下降到下一档温度时,才调低到下一档风速.如果设置为0,则一旦下降到最高档温度以下时,就立马降低到下一档风速,直到温度再次超过最高档温度值时再调高到最高风速.

Lev64Norm=1